Choosing a fabrication route for the material, duty and finish
A machine frame, stainless steel hopper and access platform may all involve welding and fabrication, but they place different demands on the workshop. Material thickness, loading, tolerances and the operating environment determine how each should be made.
The fabrication route covers the whole job: cutting the material, forming components, assembling them, welding and applying the required finish. Choosing the welding process is one part of that sequence, and it should follow the requirements of the finished steelwork.
Before welding: preparing the steelwork
Before production begins, the fabricator needs to understand what the steelwork will support, what it connects to and where accuracy matters. A machine mounting face may require closer tolerances than an adjacent guard. A hopper exposed to regular washdown needs different joint and surface details from a painted frame in a dry warehouse.
Material grade and thickness influence cutting, forming and welding choices. The specification should also identify chemical exposure, corrosion risks and any hygiene requirements. Those conditions affect the finished assembly, including its welds and areas that may be difficult to clean or coat.
Drawings are useful, but a discussion about how the equipment will be used often resolves details that dimensions alone cannot explain.
Straight sections for a support frame may be sawn to length, while sheet components may be guillotined or profile-cut. The choice depends on thickness, shape, edge quality and the accuracy needed for the next operation.
Pressing and rolling turn flat material into folded guards, curved sections or hopper components. Bend positions and allowances need to be settled before cutting. A detail that looks straightforward on a drawing may need adjustment so it can be formed without obstructing the tooling.
Components are then assembled and checked before final welding. Joint preparation, fit-up and welding sequence all matter: poor alignment can create rework, while heat can pull an assembly out of shape. Fixtures and intermediate dimensional checks help control that movement.
Choosing between MIG, TIG and laser welding
- MIG is widely used for frames, brackets and other fabricated assemblies where efficient weld deposition is important. In steelwork, the process commonly called MIG often uses an active shielding gas and is technically MAG. The gas, wire and settings must suit the material and joint.
- TIG gives the welder close control of the weld pool and is often appropriate for thin stainless steel, detailed joints and work where the finish matters. It is generally slower than MIG/MAG, so specifying it throughout an assembly may add time without improving every joint.
- Laser welding can suit thin sheet components and assemblies where limiting heat distortion and subsequent finishing is valuable. Joint fit-up, access and the required weld properties still need assessment. It is an option within the fabrication route, rather than an automatic replacement for conventional welding.
A stainless steel enclosure and a heavy support frame therefore need different decisions. The chosen process must produce the specified joint consistently; its name alone does not establish strength, cleanliness or suitability.

What coded structural welding means
Coded welding is not a separate process alongside MIG, TIG or laser. It concerns the qualifications and controls applicable to the work.
As TWI explains in its guidance on welder and procedure approval, a welder qualification demonstrates an individual’s ability within a defined range, while procedure qualification demonstrates that the welding method can produce the required properties.
For load-bearing steelwork, the project specification should establish the applicable welding procedures, qualifications and inspection requirements. These need to match the material, joint and structural duty. A neat-looking weld is not a substitute for the required checks.
Finishing also belongs in the plan. Coating preparation, stainless steel weld cleaning and specified surface finishes affect workshop time and the condition of the delivered product. Grinding welds flush should only be specified where it is appropriate to the design and service requirements.

Agreeing the fabrication route
You do not need to choose every workshop process before approaching a fabricator. Explain what the steelwork must do, share any drawings and identify the operating conditions or finish requirements that are already fixed.
Tadweld’s manufacturing team can review those requirements and discuss a suitable route for a custom fabrication project. That conversation can cover practical changes to the design, welding and finishing options, and the information needed before a quotation or production drawings are finalised.
Other News
More Insights and stories from Tadweld
Warehouse & Storage FAQs | Safe Access Regulations
October 22, 2024
Warehouse & Storage FAQs | Unsafe Access in a Warehouse
November 12, 2024